Highly Integrated
With a similar size of a FC, the 4IN1 ESC includes 4 high performance 60A BLHeli_32 DShot1200 ESCs,
a 5V BEC which can provide power for devices (i.e. FC), and a voltmeter which allows FC to monitor the
amp & volt in real time. Two ways for connecting the ESC to a FC: 1) connecting via soft cables, 2)
soldering via solder tabs are provided for selection. And the shock-absorbing design of mounting holes
effectively reduces the external vibration’s impact on high-sensitivity components and provides great
shock-absorbing protection to upper devices (i.e. FC). This ESC is designed for FPV racing.
High Quality Hardware
Large-size MOSFETs imported from Japan make the 4IN1 ESC have greater voltage/current endurance
than the last generation (at high voltages). The use of high performance 32-bit microprocessors with
operating frequency of up to 48MHz, 3-in-1 drive ICs, imported high quality ceramic capacitors,
3-ounce copper, 6 layers of PCBs guarantees less heat, higher efficiency and rapider response.
BLHeli-32 Firmware Ready
The ESC flashed with the 3rd-generation BLHeli-32 firmware has great
performance & rich functions and supports adjusting parameters or upgrading
firmware via different ways (i.e. via throttle signal wire with using other
development board or a FC flashed with the Cleanfight/Betaflight firmware).
DShot1200 Ready !
Besides the regular PWM mode, Oneshot125/Oneshot42/Multishot
modes, DShot150/300/600 modes, the latest DShot1200 mode is
also supported. In DShot1200 mode, the ESC has great
anti-interference performance and rapid response.
Hardware Generated PWM & Damped Light Mode
The ESC firmware uses hardware generated motor pwm for smooth throttle response and silent operation. Damped light
does regenerative breaking, causing very fast motor retardation, and it inherently also does active freewheeling.
Highly Integrated
With a similar size of a FC, the 4IN1 ESC includes 4 high performance 60A BLHeli_32 DShot1200 ESCs,
a 5V BEC which can provide power for devices (i.e. FC), and a voltmeter which allows FC to monitor the
amp & volt in real time. Two ways for connecting the ESC to a FC: 1) connecting via soft cables, 2)
soldering via solder tabs are provided for selection. And the shock-absorbing design of mounting holes
effectively reduces the external vibration’s impact on high-sensitivity components and provides great
shock-absorbing protection to upper devices (i.e. FC). This ESC is designed for FPV racing.

Highly Integrated
XRotor Micro 60A 4in1 BLHeli-32 DShot1200
High Quality Hardware
Large-size MOSFETs imported from Japan make the 4IN1 ESC have greater voltage/current endurance
than the last generation (at high voltages). The use of high performance 32-bit microprocessors with
operating frequency of up to 48MHz, 3-in-1 drive ICs, imported high quality ceramic capacitors,
3-ounce copper, 6 layers of PCBs guarantees less heat, higher efficiency and rapider response.

High Quality Hardware
Imported Top Quality MOSFETs
Imported High Quality
Ceramic Capacitors
High-performance
32-bit Microprocessor
3-in-1 Drive ICs
BLHeli-32 Firmware Ready
The ESC flashed with the 3rd-generation BLHeli-32 firmware has great
performance & rich functions and supports adjusting parameters or upgrading
firmware via different ways (i.e. via throttle signal wire with using other
development board or a FC flashed with the Cleanfight/Betaflight firmware).

BLHeli-32 Firmware Ready
DShot1200 Ready !
Besides the regular PWM mode, Oneshot125/Oneshot42/Multishot
modes, DShot150/300/600 modes, the latest DShot1200 mode is
also supported. In DShot1200 mode, the ESC has great
anti-interference performance and rapid response.

DShot1200 Ready !
Hardware Generated PWM & Damped Light Mode
The ESC firmware uses hardware generated motor pwm for smooth throttle response and silent operation. Damped light
does regenerative breaking, causing very fast motor retardation, and it inherently also does active freewheeling.

Hardware Generated PWM & Damped Light Mode
Specifications
Product Name
XRotor Micro 60A 4in1 BLHeli_32 DShot1200
Product Number
30902063
Specifications
Cont./Peak Current
60Ax4/ 80Ax4
Input Voltage
3-6S Lipo
BEC output
5V & 0.6A
Wires & Connectors
Input Wires
Red-12AWG-130mm/ Black-12AWG-130mm
Output Wires
No wires but solder tabs
Input Connectors
XT60(w/ Wires Soldered on)
Output Connectors
No
(Note: All the wire length above is the original length not the length you see from the outside.)
Features
Firmware
Hobbywing_XRotor_BLHeli-32 Firmware
ESC Programming
BLHeliSuite32
Stick Programming
Supported
DEO
Supported
Throttle Range Calibration
Supported
Oneshot125 Mode
Supported
Oneshot42 Mode
Supported
MultiShot Mode
Supported
DShot150/300/600/1200
Supported
Timing
Supported
Motor Rotation
Supported
Size & Weight
Size
52x42x6.6mm
Weight
15g
Applications
130-300mm FPVs